PX4 Firmware
PX4 Autopilot Software http://px4.io
sensor_params_mag1.c
Go to the documentation of this file.
1
/****************************************************************************
2
*
3
* Copyright (c) 2012-2018 PX4 Development Team. All rights reserved.
4
*
5
* Redistribution and use in source and binary forms, with or without
6
* modification, are permitted provided that the following conditions
7
* are met:
8
*
9
* 1. Redistributions of source code must retain the above copyright
10
* notice, this list of conditions and the following disclaimer.
11
* 2. Redistributions in binary form must reproduce the above copyright
12
* notice, this list of conditions and the following disclaimer in
13
* the documentation and/or other materials provided with the
14
* distribution.
15
* 3. Neither the name PX4 nor the names of its contributors may be
16
* used to endorse or promote products derived from this software
17
* without specific prior written permission.
18
*
19
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
20
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
21
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
22
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
23
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
24
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
25
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
26
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
27
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
28
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
29
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
30
* POSSIBILITY OF SUCH DAMAGE.
31
*
32
****************************************************************************/
33
34
/**
35
* ID of Magnetometer the calibration is for.
36
*
37
* @category system
38
* @group Sensor Calibration
39
*/
40
PARAM_DEFINE_INT32
(CAL_MAG1_ID, 0);
41
42
/**
43
* Mag 1 enabled
44
*
45
* @boolean
46
* @category system
47
* @group Sensor Calibration
48
*/
49
PARAM_DEFINE_INT32
(CAL_MAG1_EN, 1);
50
51
/**
52
* Rotation of magnetometer 1 relative to airframe.
53
*
54
* An internal magnetometer will force a value of -1, so a GCS
55
* should only attempt to configure the rotation if the value is
56
* greater than or equal to zero.
57
*
58
* @value -1 Internal mag
59
* @value 0 No rotation
60
* @value 1 Yaw 45°
61
* @value 2 Yaw 90°
62
* @value 3 Yaw 135°
63
* @value 4 Yaw 180°
64
* @value 5 Yaw 225°
65
* @value 6 Yaw 270°
66
* @value 7 Yaw 315°
67
* @value 8 Roll 180°
68
* @value 9 Roll 180°, Yaw 45°
69
* @value 10 Roll 180°, Yaw 90°
70
* @value 11 Roll 180°, Yaw 135°
71
* @value 12 Pitch 180°
72
* @value 13 Roll 180°, Yaw 225°
73
* @value 14 Roll 180°, Yaw 270°
74
* @value 15 Roll 180°, Yaw 315°
75
* @value 16 Roll 90°
76
* @value 17 Roll 90°, Yaw 45°
77
* @value 18 Roll 90°, Yaw 90°
78
* @value 19 Roll 90°, Yaw 135°
79
* @value 20 Roll 270°
80
* @value 21 Roll 270°, Yaw 45°
81
* @value 22 Roll 270°, Yaw 90°
82
* @value 23 Roll 270°, Yaw 135°
83
* @value 24 Pitch 90°
84
* @value 25 Pitch 270°
85
*
86
* @min -1
87
* @max 30
88
* @reboot_required true
89
* @category system
90
* @group Sensor Calibration
91
*/
92
PARAM_DEFINE_INT32
(CAL_MAG1_ROT, -1);
93
94
/**
95
* Magnetometer X-axis offset
96
*
97
* @category system
98
* @group Sensor Calibration
99
*/
100
PARAM_DEFINE_FLOAT
(CAL_MAG1_XOFF, 0.0
f
);
101
102
/**
103
* Magnetometer Y-axis offset
104
*
105
* @category system
106
* @group Sensor Calibration
107
*/
108
PARAM_DEFINE_FLOAT
(CAL_MAG1_YOFF, 0.0
f
);
109
110
/**
111
* Magnetometer Z-axis offset
112
*
113
* @category system
114
* @group Sensor Calibration
115
*/
116
PARAM_DEFINE_FLOAT
(CAL_MAG1_ZOFF, 0.0
f
);
117
118
/**
119
* Magnetometer X-axis scaling factor
120
*
121
* @category system
122
* @group Sensor Calibration
123
*/
124
PARAM_DEFINE_FLOAT
(CAL_MAG1_XSCALE, 1.0
f
);
125
126
/**
127
* Magnetometer Y-axis scaling factor
128
*
129
* @category system
130
* @group Sensor Calibration
131
*/
132
PARAM_DEFINE_FLOAT
(CAL_MAG1_YSCALE, 1.0
f
);
133
134
/**
135
* Magnetometer Z-axis scaling factor
136
*
137
* @category system
138
* @group Sensor Calibration
139
*/
140
PARAM_DEFINE_FLOAT
(CAL_MAG1_ZSCALE, 1.0
f
);
f
Vector< float, 6 > f(float t, const Matrix< float, 6, 1 > &, const Matrix< float, 3, 1 > &)
Definition:
integration.cpp:8
PARAM_DEFINE_INT32
PARAM_DEFINE_INT32(CAL_MAG1_ID, 0)
PARAM_DEFINE_FLOAT
PARAM_DEFINE_FLOAT(CAL_MAG1_XOFF, 0.0f)
src
modules
sensors
sensor_params_mag1.c
Generated by
1.8.13